Pillow With Button Letter

Add some charm with buttons!  Make your own pillow or add a button letter to pre-made pillow.

Materials:

  • Fabric to make pillow (1 yard for 18″ pillow) or ready made pillow
  • Buttons in different sizes
  • Needle
  • Thread and DMC floss (cross stitching thread)
  • Paper to make your letter pattern
  • Dressmaker’s Marking Pencil or chalk
  • Pillow form (inside stuffing) I’m using a 14″
  • Ruler
  • Sewing machine, scissors
  • Embroidery hoop (optional)

Directions:

Start by cutting your pillow front an 19” square ( I’m making an 18″ pillow with a pillow form of 14″). For the back cut two pieces 19″ by 12″.  This is going to be a simple pillow with an opening in the back for the pillow form to side in.  On a piece of paper draw out and cut our letter, I’m doing an R.  Place on top of our 19″ front of pillow, when you have it centered or where you want it, trace the outline with the marking pencil or chalk.

Now I have my R outline, with matching DMC floss (or thread) do a quick stitch on chalk line to outline the letter.

I”m leaving the outline of the R on my pillow but if you wanted to do a quick stitch with thread and then pull out the thread after you sew that buttons that also looks good.  By doing the stitch outline it makes it so much easier.

Now for button fun.  Use your paper letter as a pattern for your buttons.  This will help you see where the buttons should be sewn and just how many button you need before you start sewing.  I did not use a embroidery hoop, I think it would have made it easier to sew on the buttons.

Start sewing buttons and more buttons.  I found when sewing that I needed to shift and add or move some buttons from how I had them on the pattern.  Notice that I stacked a smaller button on top of a larger ones.

Now we need to make the pillow.  First turn back twice and sew down the 19″ side of each back piece.  Place the front of pillow right side up and place on back piece on top with right sides together.

Now place the other back piece on top, pin in place and sew all four sides.  Turn pillow right side out and lay flat (maybe iron around the edges).  With a ruler and chalk  mark each corner 2″ in and down (remember I’m using a 14″ pillow form for the inside).  And sew all four sides of the pillow 2″ in, this will make a 14″ square in center.

All that is left to do is slide in the pillow form and enjoy.

How cute it would be to sew a button letter on a fabric purse or tote bag, too!

 

 

 

 

Fall Pillows

A super fast and easy way to change the look of your room from season to season is to create new slip covers for your accent pillows. The possibilities for pillow covers are truly are endless;  I am showing you just one way to make slip covers, but let your creative side out and have fun with this one!

First pick your fabric for the pillow, if you like (or need) to wash the covers often,  just  make sure the fabric you choose is durable and able to be washed often.  I used 2 yards of fabric for the 3 pillows.  I made my 18″, because that is the size pillow foams (the inside stuffing) that looks best in my room.  You might like a different size, in the stores (like Jo Ann) they will carry a range of sizes and shapes.

Start by cutting – since my pillow is going to be a finished 18″, I cut a 19″ square (times 3 for 3 pillows) and for the back cut 12″ by 19″ (times 3) and 10″ by 19″ (times 3).

When creating any design or embellishment details on a pillow, you want to do that before sewing the pillow together, so let’s start with the fun fall designs. I embellished these fall pillows with felt and DMC thread (cross stitching).

Begin by making your design.  I wanted a tree, and tree branch and a flower.  Since my design was going to be large, I used newspaper to draw out my shapes.

Lay out your cut out felt shapes on the top of your 19″ fabric square (top of pillow).  Pin pieces in place.

With matching thread I did a quick stitch around the branch.  Then add the leaves, stitching down the center of each leaf.

Now for the slip pillow with the flower (I always need a flower somewhere 🙂 ).

Cut a quick flower shape – about 3″. You will need 7 and a 2″ circle for the flower base.

Take each flower shape and fold in half and fold again, pin to hold.  Do this to all 7.

Keep the pin in and cut the tip off.  With needle and thread, stitch along bottom (where you just cut).

Place 4 of the flower petals on felt circle and sew (because I’m putting the flower on a pillow sewing on gluing is best).

Sew on the other 3 petals.  For the center, cut a piece about 1/2″ by 2 1/2″.  Roll long ways and stitch in center.

For the flower buds, I made 3 petals ( cutting the flower shape, folding and folding).  This time I did not cut bottom.  I used a half circle, and wrapped the base of flower and sewed in place.

For the smaller bud I used one petal.  Play around and find what you like.

Sew your flower and buds to the pillow top.  I finished by adding leaves and a stem.

To make the stems with a quick stitch, I used straight pin to mark out my stem shape.  Make it so much easier, just stitch along the pins.

 

Now, it’s time to make the slipcovers! Cut a strip (one for each pillow you’re making); I made mine 2″ and 6″.  Fold over the 2″ side and sew down the 6″ side.

Clip the fabric to make it easier for turning. Use a safety pen to pull through.  You have the loop for the back.

Sew  back piece 12″X 19″  down one side of the 19″ side.  You will fold over raw edge and sew and fold that over and sew again (on raw edge).

Take the 10″ by 19″ back piece and fold over raw edge 19″ side one time.  Fold in half, marking the center (the side that you just sewed). Place your loop on the center mark, turn and sew back edge that was just sewn.

Are you with me so far?  We are almost there! Now, think backwards – lay your piece with the loop down first, then the other back piece (they will overlap).  You have a 19″ square and you want to pin all around your pillow to hold all pieces in place.  Start sewing your pillow together( I used a 5/8 seam).  You need to clip around all sides, and I like to cut off each corner (see pic).

You made a slip cover pillow.  Turn your pillow right side out.  Mark where your button goes ( this will hold the pillow together).  Sew your button on.  Done!  Much easier than a zipper (and the back even looks great too).

These simple designs are quick and easy, let your creative side out and have fun designing you own custom slip cover pillows!

 

I’m sharing this tutorial with Happy Hour, Patches of Pink, RoCa & Company, & Kissed by a Frog.

Related Posts Plugin for WordPress, Blogger...